Bennett/Trex/HCMI Parts
HCMI Driver assembly with exchange plus shipping
FET Driver assembly
#E10134
Our drivers are used/tested or rebuilt with new FET's / diodes and tested.
Enersys (Hawker) Cyclon 0819-0020
​
​D-Cell 12 Volt/2.5 Amp Hour Sealed Lead Acid Battery.
Batteries for Bennett/Trex/HCMI SE
Stored Energy generators
Before replacing driver assemblies we recommend reading the advanced troubleshooting guide
Bennett kV Regulator board
Part #208089
Bennett / HCMI IGBT Drivers
Bennett FET Driver Assy
Bennett Regulated Power Supply Board
with exchange of your old board
There are two different versions of this board by the same part number. The 50 volt version and the 30 volt version. If the Filament Reg bd is a 208090 you need the 30 volt. If it's 208163, then you need the 50 volt version. HCMI were all 50 volt version.
Bennett part # 208084
HCMI Part # A-184
Bennett/Trex IGBT driver assy with exchange plus shipping
Part # E10224
Any parts listed for exchange, requires the old part to be returned to us within 15 days from receipt. Standard ground shipping is ok. Failure to return the old part will result in an additional billing of the original part price. If you order a $400 part with exchange and you do not return the old part, you will be billed an additional $400. We would much rather have the old part back than the additional billing. Many of these parts are in short supply. As a courtesy to others, please return the old parts in a timely manner.
Bennett Microprocessor board for HFQ 1000 series generator part #208116
plus shipping with exchange
(please specify Bennett model)
Bennett 100 series Operator Console
OCP with exchange.
Part# 10125
Bennett Microprocessor board for HFQ 100 series generator part # 208072
plus shipping with exchange
Bennett 6-way logic board for elevating
table.
Bennett part # 208108
Bennett power shut-off board
Bennett part # 208101
Bennett power shut-off board
Bennett part # 208087
(as used in SE Stored Energy)
Select the shipping method from the drop down menu above the "Buy Now" button
Bennett Filament Regulator Board
Part # 208090
with exchange, plus shipping
Bennett Collimator knobs
D50-M
D100082-1 (original part #)
These are not the exact same
knob, but most similar that
are available. Exact same
diameter shaft, shaft is slightly
longer, knob diameter is some
what smaller, but they work. The
original knobs are no longer
available.
Diameter of the knob shaft is exactly the same as the original knobs. No modification of collimator case hole is required. Since the knob shaft is longer, there will be approximately 1/4" gap from the bottom of the knob to the metal case of the collimator.
Bennett power shut-off board
Bennett part # 208122
(as used in 1000 series / 3phase gen)
Bennett 100 Series OCP LCD Display
Part # E10123 NEW, no exchange
$224.00 with standard ground shipping
Also used in HCMI consoles
Bennett Source Charger Board for SE
Part # 208088
HCMI Source Charger Board for SE
Part# A-288
Bennett Filament Regulator Board
Part# 208163
with exchange, plus shipping
Bennett 1000 Series OCP LCD Display
Part # 205036 or DMF 5003
Original displays are no longer available
New Display $485.00, plus shipping
Orginal display, older CCFL backlight technology
New display with LED backlight technology
Bennett Collimator
New Mirror with Filter
Mounting bracket assembly
Part # D6100049
For D-50M & D70A collimators
The old filter/mirror assy must be returned
Mounting is exactly the same as the old display, same size and same mounting tabs/spacing. Requires a simple +5 vdc connection for backlight inside the console
HCMI Chip U2
Version 5.16
Eliminates Code Board Option
Bennett Tubestand/Table 24VDC
Magnetic Lock
Bennett Part# 200025
New, as pictured, no wires included
Bennett/HCMI troubleshooting when display boots to: "DC Ref error" Click here
Select the shipping method from the drop down menu above the "Buy Now" button
Select the shipping method from the drop down menu above the "Buy Now" button
Bennett/HCMI Fuse Holder Designation Click here
For original Bennett generators
Original Bennett part# 101671
Bennett 1000 Series Switch Panel
All Bennett/HCMI P.C. boards have a 90 day repair or replacement warranty and any shipping charges are non-refundable
Bennett/HCMI troubleshooting SES errors Click here and also see the advanced troubleshooting guide above
And for newer Bennett as made by Summit
Requires the old console to be returned to us within 15 days
Complete with 20ft+ ribbon cables, new display and new switch panel
Part# SW-CON-HCMI
You can also use the arrow down button to select faster shipping above
And for newer Bennett as made by Summit
SW-0045
Now improved with a metal back plate to prevent the panel from flexing and failing. Thickness of panel is the same as the original. Fits and works perfectly.
Click the arrow down symbol after "USD" to select faster shipping
Click the arrow down symbol after "USD" to select faster shipping
Click the arrow down symbol after "USD" to select faster shipping
Select the shipping method from the drop down menu above the "Buy Now" button
HCMI
A-272 Microprocessor p.c.b
Plus shipping w/exchange
90 day warranty
Bennett/HCMI SE battery location, wiring and charger board calibration, Click here
Bennett/HCMI Cabinet Photo Click Here
